Code
Explanation
(2) Item Number. Indicates the item number or
dollar value, critical material or hazardous
reference designation used to reference the item in the
material).
illustration.
b. Federal Stock Number. Indicates the Federal
stock number assigned to the item and will be used for
1-4.
Special Information
requisitioning purposes.
a. Usable on codes are included in column 3.
c. Description. Indicates the Federal item name
Uncoded items are applicable to all models.
and a minimum description required to identify the item.
Identification of the usable on codes used in this
publication are
The last line indicates the reference number followed by
the applicable Federal Supply Code for Manufacturer
(FSCM) in parentheses. The FSCM is used as an
Code
Used on
element in item identification to designate manufacturer
ALO
AN/URM-79
or distributor or Government agency, etc., and is
identified in SB 708-42.
b. The following publications
pertain
to
the
d. Unit of Measure (U/M). Indicates the standard or
AN/URM-79 and its components:
basic quantity by which the listed item is used in
performing the actual maintenance function.
This
TM 11-5094
Frequency Meters AN/URM-79
measure is expressed by a two-character alphabetical
and AN/URM-82.
abbreviation; e.g., ea, in, pr, etc., and is the basis used to
TM 11-6625-300-20P
Organizational
Maintenance
indicate quantities and allowances in subsequent
Repair Parts and Special
columns. When the unit of measure differs from the unit
Tools Lists:
of issue, the lowest unit of issue that will satisfy the
Frequency Meter AN/URM-79.
required units of measure will be requisitioned.
e. Quantity Incorporated in Unit. This column
1-5.
Location of Repair Parts
indicates the quantity of the item used in the equipment.
a. This manual contains one cross-reference index
Subsequent appearances of the same item in the same
assembly are indicated by the letters "REF".
Federal
stock
number
or
reference
number
f. 30-Day DS/GS Maintenance Allowances.
(manufacturer's part number) is known. The first column
NOTE
in the index is pre-
Allowances in GS column are for GS
pared in numerical or alphanumeric sequence in
maintenance only.
ascending
order.
The
reference
numbers
(manufacturer's part numbers) are listed immediately
(1) The repair parts indicated by asterisk entries
following the last listed Federal stock number in the
in separate allowance columns for DS and GS represent
index of Federal stock numbers.
those authorized for use at that category of maintenance
b. When the Federal stock number or reference
to be requisitioned on an "as required" basis, until
number is known, follow the procedures- given in (1) and
stockage is based on demand in accordance with AR
(2) below.
710-2.
(1) Refer to the index of Federal stock numbers
(2) Allowance quantities are indicated in the
special tool lists section for special tools, TMDE, and
reference number. The FSN and reference number are
other support equipment.
cross-referenced to the applicable figure and item
g. 1-Year
Allowances
Per
100
number or reference designation.
Equipments/Contingency Planning Purposes. Column
(2) Refer to the repair parts list (sec II) and
intentionally left blank.
locate the figure number (col 10a) and item number or
h. Depot Maintenance Allowance Per 100
reference designation (col 10b) as noted in the FSN
Equipments. This column indicates opposite the first
index.
appearance of each item the total quantity authorized for
c. When the figure and item number or reference
depot maintenance of 100 equipments.
designation are known, scrutinize columns 10a and 10b
i. Illustration. This column is divided as follows:
of the repair parts list (sec II) until the item is located.
(1) Figure number. Indicates the figure number
d. When the FSN, reference number, figure
of the illustration on which the item is shown in TM 11-
5094.
4
Previous Page
